Guest at the entrance door of the community life. It is allowed to install the mounting boards of the other design. I community life

assertionsta introductions u diyu

Decree of the Derzhbud SRSR

STATE STANDARD SPLIT RSR

WOODEN DOORS FOR RESIDENTIALS I

GROMADSKIKH BUDIVEL

TYPI, DESIGN THAT ROZMIRI

Wooden external doors for dwellings and public

buildings. Types, structure and dimensions

GOST 24698-81

Group Zh32

OKP 53 6110; OKP 53 6196

Introduction term

Rozrobleno Sovereign committee of civil life and architecture under the Derzhbudi SRSR.

Vikonavtsi: Yu.O. Argo (Kerivnik temi), Ph.D. tech. sciences; I.V. Strokiv; I.S. Posilska; G.G. Kovalenko; PER. Burkova; G.V. Levushkin.

Introductions by the Sovereign Committee on Civil Life and Architecture under the Derzhbudi SRSR;

Deputy head S.G. Zmeul.

This standard is expanding on wooden doors for living quarters community life, as well as for additional budіvel and the use of enterprises of different galluses of the people's state.

The standard does not appear on the doors of unique public buildings: railway stations, theatres, museums, sports palaces, exhibition pavilions, palaces of culture.

1. TIPI, ROZMIRI AND MARK

1.1. Doors, which are prepared according to this standard, fall into the following categories:

H - entrances and tambours;

W- Services;

L - hatches and lazi.

1.2. Doors of type H are made from shield and frame canvases. Frame canvases can be smart. Doors of types C and L are made from panel boards. Shield cloths can be prepared with batten sheathing.

Doors of types H and C are made with single-panel and double-panel, glued and blind canvases, with a threshold and without a threshold.

1.3. All doors, which are prepared according to this standard, are brought up to the doors of increased moisture resistance.

1.4. dimensions the doors of the guilty will be assigned to the devil. 1. Razmіri on armchairs to the standard given for non-barvllennyh vrobіv and parts in mm. Rosemary opened at the preliminary Addendum 1.

DIMENSIONS OF DOORS ROSE

Damn. one

For the sake of comfort with the acceptance of a virobnik, it is allowed to change the little ones sklinnya for the rahunok, change the rozmirіv skla or their articulation, as well as zastosuvannya of deaf canvases.

Door leafs of type C, which are upholstered on two sides with thin-sheet galvanized steel according to GOST 7118-78, can be expanded in width by 6, and in height by 5 mm less, lower for canvases without upholstery.

Doors of type C can be equipped with doors with a strong seal and a reinforced frame according to GOST 6629-74.

1.5. Such a structure of mental designation (brand) of doors is being established.

XX X-XX X

─┬─ ─┬─ ─┬──┬─ ─┬─ ─┬─

││││││

└───┼───┼─────┼───┼───┼──── Type of door: D - doors

└───┼─────┼───┼───┼───── Virobu type:

││││Н - input chi tambour;

││││С - service;

││││L - hatch abo laz

└─────┼───┼───┼──── Expanding the opening by height in dm

└───┼───┼──── Expanding the opening in width in dm

└───┼──── Letters that mean:

│A, B and C - variants of small ones

│one rosemary;

│G - doors are deaf;

│К - doors with hitny canvases -

│L - doors left;

│П - doors with a threshold;

│Т - doors important to burn;

│U - insulated doors;

│Sch - shield doors;

│Р1 and Р2 - sheathing and її tipi

└──── Assigned to the standard

Apply clever words:

entrance doors or tambour single-pane doors for a pier with a height of 21 and a width of 9 dm, glazed, with the right board panel canvas, with a threshold, with type 2 sheathing:

DN 21-9PShchR2 GOST 24698-81

the same, with the left navazhka of the frame canvas:

DN 21-9LP DERZHSTANDARD 24698-81

entrance doors or tambour doors with smart canvases for an opening with a height of 24 and a width of 15 dm:

DN 24-15K GOST 24698-81

double-deaf service doors, for opening with a height of 21 and a width of 13 dm, insulated:

DS 21-13GU GOST 24698-81

a single-panel hatch for a hole with a height of 13 and a width of 10 dm:

DL 13-10 GOST 24698-81

2. VIMOGY TO CONSTRUCTION

2.1. The doors of the hinged vygotovlyatsya vіdpovіdno up to GOST 475-78, which is the standard for working chairs, hardened in the prescribed manner.

2.2. The design, shape and type of doors according to the fault are assigned to the characteristic. 2 - 5, and the expansions of the resizes - in fig. 6 - 13.

DESIGN, SHAPE AND DOORS

Shield doors

Retin details div. in fig. 6 - 8.

Damn. 2

Frame doors

Retin details div. in fig. 9.

Damn. 3

Retin details div. in fig. ten.

Damn. four

TYPE OF W

Shield doors important and insulated

TYPE L

Luki ta lazi

Retin details div. in fig. 11 - 13.

Damn. 5

TYPE H

Shield doors

Peretin A 1

Peretin A 2

Damn. 6. Retin of door parts

Peretin A5

Peretin A 6

Option with lining

Damn. 7

Panel doors with sheathing

Damn. eight

TYPE H

Frame doors

Damn. 9

Peretin V 1

Peretin V 2

Peretin B3

Peretin V 4

Peretin B5

Damn. ten

Framed doors with hit canvases

Peretin G 1

Peretin G 2

Peretin G3

Peretin G 4

Damn. eleven

TYPE OF W

Shield doors

Important borrowers

Damn. 12

Warming

Damn. 12

TYPE L

Luki ta lazi

Damn. 13

2.3. Cloths of shield doors are due to be prepared from the succulent fittings of the shield calibrated according to the tovshchina. wooden slats.

Door cladding is carried out with materials up to GOST 475-78 at the part, which can be applied to the doors to increase moisture resistance.

For succulent lining of doors from the outer side with profiled rails according to GOST 8242-75 for a ball of parchment according to GOST 2697-75, or for galvanized steel lining according to GOST 7118-78, solid wood fiber slabs of the T-400 brand according to GOST 4598-74 or glued plywood of the FK brand according to GOST 3916-69. Tambour doors can be made without sheathing with wooden laths. The rails are fastened with screws GOST 1144-80 or with GOST 4028-63 screws with a length of 40 mm with anti-corrosion coating. The maximum kr_plen krіplen - 500 mm. The fastening in the skin row is due to the butt stitching on one level along the entire width of the canvas.

2.4. The lower parts of the door leafs of type H are due to the protection of wooden planks with a thickness of 16 - 19 mm or swags with decorative paper-ball plastic with a thickness of 1.3 - 2.5 mm according to GOST 9590-76, overhard wood fiber plates with a thickness of 3.2 - 4 mm according to GOST 4598-74, thin-sheet galvanized steel. Wood and plastic materials are fastened with waterproof glue and screws with anti-corrosion coatings, and steel smugs are fastened with 30-40 mm bolts according to GOST 1144-80. Krok fastening outside the perimeter of 100 mm. Razmіri zahishnikh planks and smog are shown in fig. 6 - 11.

2.5. Canvases and boxes important burners and insulated doors of type C should be protected with thin-sheet galvanized steel with a thickness of 0.35 - 0.8 mm according to GOST 7118-78 on all surfaces of both sides, as indicated in fig. 12. The leaves began to merge into a single fold.

2.6. canvases important burners doors type Z both sides are covered with balls of asbestos cardboard with a thickness of 5 mm according to GOST 2850-75.

Cloths of insulated doors of type C are covered from one side with a ball of soft fibrous wooden boards with a thickness of 12 mm according to GOST 4598-74. On the perimeter of the canvas, on the side of the insulation, fasten with flowers or self-tapping screws wooden slats 12 x 30 mm, fastening 100 - 150 mm.

2.7. For folding doors, fix a door stopper 4 - 5 mm according to GOST 111-78.

It is also difficult to find on a window of 800 mm, or less at the bottom of the canvas, and with different glasses of a large format, it is necessary to install a fence.

Apply the installation of winter fences in the recommended Addendum 2.

Tovshchina skla, design of zahisnih gratings and changes in the design of doors, connected with the installation of electric locks, must be ordered at work chairs.

2.8. For mechanical protection, noise reduction and heat loss of type H doors are equipped with door locks type ZD1 according to GOST 5091-78, thickening gaskets according to GOST 10174-72 or porous gumi according to GOST 7338-77, DR09 78. bolts ZT or bolts ShV according to GOST 5090-79.

2.9. The need to complete the doors with locks, according to GOST 5089-80, is due to buti is designated in the lock.

2.10. Raztashuvannya priladіv and їх types induced in the binding Addendum 3.

2.11. At the request for the delivery of doors, the following may be indicated:

the number of doors according to the brands that are assigned to the standard;

type and color of processing;

tovshchina warehouse;

specification of accessories

Addendum 1

Dovidkove

ROZMIRI DOOR OPENINGS AT THE WALLS

TYPE H

Note. At the temples, there are openings for openings for doors that are used.

TYPE OF W

TYPE L

APPLY THE INSTALLATION OF THE ZAKHISNY GARDEN

Wooden fence

metal fences

Addendum 3

Obov'yazkove

POSITIONING OF FITTINGS AT THE DOOR

Single sawdoor types H and C

Double doors type H and C

Doors type L

Loop for counter

Notes. 1. Doors of type Z are not fitted with curves.

2. The locks are installed at the paddocks, which are replaced by working chairs.

3. Staple handles can be installed vertically or horizontally.

4. Loops for counters are installed in single-panel hatches. It is allowed to fix the loops of the other design.

GOST 24698-81 UDC 691.11.028.1:006.354 Group Zh32 STATE STANDARD SSR SPLIT DOORS FOR RESIDENTIAL AND GREAT BUILDINGS Types, structure and dimensions OKP 53 6110; OKP 53 6196 to the Decree of the Sovereign Committee of the SRSR on the right of everyday life on April 13, 1981. No. 51 the term was introduced on 01.01.1984. ROZROBLEN by the Sovereign Committee for Civil Life and Architecture under the Derzhbudi SRSR. tech. sciences; I. V. Strokov; I. S. Posilska; G. G. Kovalenko; Z. A. Burkova; G. V. Levushkin INTRODUCED by the Sovereign Committee for Civil Life and Architecture under the Derzhbudi SRSR Zast. Head S. G. Zmeul OF THE STATEMENTS AND INTRODUCTIONS TO THE DIVISION OF THE STATE COMMITTEE OF THE SRSR on the right of everyday life on April 13, 1981. № 51 Non-compliance with the standard to be followed by the law that appropriation of the undertakings of the various galluses of the people's state. The standard does not appear on the doors of unique public buildings: railway stations, theatres, museums, sports palaces, exhibition pavilions, palaces of culture. 1. TYPI, ROZMIRI AND MADE 1.1. Doors, which are prepared according to this standard, fall into the following categories: H - entrances and vestibules; C - services; L - hatches and lazi. 1.2. Doors of type H are made from shield and frame canvases. Frame canvases can be smart. Doors of types C and L are made from panel boards. Shield cloths can be prepared with batten sheathing. Doors of types H and C are made with single-panel and double-panel, glued and blind canvases, with a threshold and without a threshold. 1.3. All doors, which are prepared according to this standard, are brought up to the doors of increased moisture resistance. 1.4. Dimensional dimensions of the doors according to the requirements are indicated on the characteristic. 1. The dimensions on the armchairs are given to the standard for non-barrier types and details in mm. 1. Due to the weather, it is allowed to change the babies of the sklinnya for the rahuk, to change the rozmirіv skla or their articulation, as well as to zasosuvannya deaf canvases. Door leafs of type C, which are upholstered on two sides with thin-sheet galvanized steel according to GOST 7118-78, can be expanded in width by 6, and in height by 5 mm less, lower for canvases without upholstery. Doors of type C can be equipped with doors with a strong seal and a reinforced frame according to GOST 6629-74. 1.5. Such a structure of mental designation (brand) of doors is being established. Apply the following designations: entrance doors or vestibule single-saw doors for an opening with a height of 21 and a width of 9 dm, glazed, right on the panel canvas, with a threshold, with type 2 sheathing: DN 21-9PSHHR2 GOST 24698-81: DN 21-9LP DERZHSTANDART-24698-81 81 doors for entrances or tambours with hitny canvases for an opening with a height of 24 and a width of 15 dm: DN 24-15K GOST 24698-81 doors for service double-deaf D1 21-13GU GOST 24698-81 a single-panel hatch for an opening of a curtain 13 and a width of 13 -10 GOST 24698-81 2. VIMOGI BEFORE DESIGN 2.1. The doors of the hinged vygotovlyatsya vіdpovіdno up to GOST 475-78, which is the standard for working chairs, hardened in the prescribed manner. 2.2. The design, shape and type of doors according to the fault are assigned to the characteristic. 2 - 5, and the expansions of the resizes - in fig. 6 - 13. 2.3. Cloths of shield doors are made from the core of the shield, calibrated according to the composition of the wooden slats. Door cladding is carried out with materials up to GOST 475-78 at the part, which can be applied to the doors to increase moisture resistance. For sutsile door siding from the outer side with profiled rails per GOST 8242-75 for parchment ball per GOST 2697-75 or for galvanized steel siding per GOST 7118-78, hard wood-fiber boards of the T-440 FK grade per GOST 3916-69 are allowed. Tambour doors can be made without sheathing with wooden laths. The rails are fastened with screws GOST 1144-80 or with GOST 4028-63 screws with a length of 40 mm with anti-corrosion coating. The maximum kr_plen krіplen - 500 mm. The fastening in the skin row is due to the butt stitching on one level along the entire width of the canvas. 2.4. The lower parts of the door leafs of type H are due to the protection of wooden planks with a thickness of 16 - 19 mm or swags with decorative paper ball plastic with a thickness of 1.3 - 2.5 mm according to GOST 9590-76, overhard wood fiber boards with a thickness of 3.2 - 4 mm for GOST 4-74, thin-sheet galvanized steel. Wood and plastic materials are fastened with waterproof glue and screws with anti-corrosion coatings, and steel smugs are fastened with 30-40 mm bolts according to GOST 1144-80. Krok fastening outside the perimeter of 100 mm. Razmіri zahishnikh planks and smog are shown in fig. 6 - 11. 2.5. Cloths and boxes of fireproof and insulated doors of type C should be protected with thin-sheet galvanized steel 0.35 - 0.8 mm according to GOST 7118-78 on all surfaces of both sides, as indicated in fig. 12. The leaves began to merge into a single fold. 2. 6. Cloths of high-quality doors of type Z both sides are covered with balls of asbestos cardboard with a thickness of 5 mm according to GOST 2850-75. Cloths of insulated doors type Z are covered from one side with a ball of soft wood fiber boards with a thickness of 12 mm according to GOST 4598-74. On the perimeter of the canvas, on the side of the insulation, fasten with flowers or self-tapping screws wooden slats 1230 mm, fastening 100 - 150 mm. 2.7. For folding doors, fix a door stopper 4 - 5 mm according to GOST 111-78. It is also difficult to find on a window of 800 mm, or less at the bottom of the canvas, and with different glasses of a large format, it is necessary to install a fence. Apply the installation of zahisnyh fences in the recommended addendum 2. Warehouse construction, design of zahisnyh gates and changes in the design of doors, connected with the installation of electric locks, due to the order at the working chairs. 2.8. For mechanical protection, noise reduction and heat loss of type H doors are equipped with door locks type ZD1 according to GOST 5091-78, thickening gaskets according to GOST 10174-72 or porous gumi according to GOST 7338-77, DR09 78. bolts ZT or bolts ShV according to GOST 5090-79. 2.9. The need to complete the doors with locks, according to GOST 5089-80, is due to buti is designated in the lock. 2.10. Raztashuvannya priladіv and їх types induced at the obov'yazkovomu dodatka 3. 2.11. At zamovlennі on the supply of doors can be assigned: the number of doors by brand that is assigned to the standard; type and color of processing; tovshchina warehouse; specification of accessories DIMENSIONAL DESIGNS OF DOORS Notes: 1. Schemes of doors are shown on the side of the facade. 2. The numbers above the door schemes indicate the expansion of opening doors. 3. Rosemary in shackles is given for doors 21-15A, 21-19, 24-15A and 24-19 with smart canvases. 4. Doors 21-9 and 21-13A are designed for single-surface doors and smіttєpriymalnyh priymіschen. Damn. 1 CONSTRUCTION, SHAPE AND DOORS DOORS Doors shields in fig. 6 - 8. Damn. 2 doors frame in fig. 9. Damn. 3 Retin details div. in fig. 10. Damn. 4 Doors framed with chimney canvases TYPE C Doors shielded and insulated TYPE L Hatches and lazi Peretin details div. to hell. 11 - 13. Damn. 5 TRANSFER OF DOOR DETAILS TYPE H Shield doors Peretin A1 Peritin A2 Chort. 6 Retin A3 Retin A4 Retin A5 Retin A6 Option with lining Chart. 7 Shield doors with sheathing Peretin A1 Peretin A3 and A4 Peretin A2 Peretin A5 Chort. 8 TYPE N Frame doors Peretin B1 Peretin BZ Pereriz B2 Peretin B4 Chort. 9 Peretin B1 Peretin B3 Peretin B2 Peretin B4 Chart. 10 Doors framed with hitny canvases Peretin G1 Peretin G3 Peretin G2 Peretin G4 Chort. 11 TYPE Z Doors of shields Important occupiers Retin D1 Retin D3 Retin D2 Retin D4 Chort. 12 Insulation Peritin El Peritin E3 Peritin E2 Peritin E4 Chort. 12 TYPE L Hatches and lazi Peretin Zh1 Peretin Zh3 Peretin Zh2 Chort. 13 ADDITION 1 DOVIDKOVE DESIGN OF DOOR WALLS TYPE N Note. At the temples, there are openings for openings for doors that are used. TYPE H TYPE L ADDITION 2 RECOMMENDED APPLICATION INSTALLATIONS FOR HARDENING FENCES Wooden fences Metal fences ADDITION 3 Obov'yazkove POSITIONING OF ACCESSORIES AT THE DOORS Single-pane doors of types H and D are installed. 2. The locks are installed at the paddocks, which are replaced by working chairs. 3. Staple handles can be installed vertically or horizontally. 4. Loops for counters are installed in single-panel hatches. It is allowed to fix the loops of the other design.

GOST 24698-81

INTERNATIONAL STANDARD

WOODEN DOORS

FOR RESIDENTIAL

I GROMADSKIKH BUDIVEL

TYPI, DESIGN THAT ROZMIRI

Vidannya official

Standardinform

UDC 691.11.028.1:006.354

INTERNATIONAL

Group J32 STANDARD

WOODEN DOORS FOR RESIDENTIALS AND PUBLIC BUILDINGS

Tipi, design and expansion

Wooden external doors for residential and public buildings.

Types, structure and dimensions

MKS 91.060.50

OKP 53 6110; OKP 53 6196

Entered date 01.01.84

This standard is being expanded on wooden zvnishnі rozpashnі doors for living quarters and hromada budіvel, as well as for additional budіvel and priznієmstv pіznі іnіshnі galuzi people's gospodarstva.

The standard does not appear on the doors of unique public buildings: railway stations, theatres, museums, sports palaces, exhibition pavilions, palaces of culture.

1. TIPI, ROZMIRI AND MARK

1.1. Doors in the fallow area are subdivided into types: H - entrances and vestibules; C - services; L - hatches and lazi.

1.2. Doors of type H are made from shield and frame canvases. Frame canvases can be smart. Doors of types C and L are made from panel boards. Shield cloths can be prepared with batten sheathing.

Doors of types H and C are made with one- or two-panel, glued and blind canvases, with a threshold or without a threshold.

1.3. All doors are brought up to the level of increased moisture resistance.

1.4. Dimensional dimensions of the doors according to the requirements are indicated on the characteristic. 1. Rozmiri on armchairs is given for uncomplicated variations and details in millimeters. Rozmіri prorіzіv induced at addendum 1.

For the sake of comfort with the admission-virobnik, it is allowed to change the little ones sklinnya for the rahunok, change the fold or their articulation, as well as zastosovuvat deaf canvases.

Door leafs of type C, which are upholstered on both sides with thin-sheet galvanized steel according to specifications for steel of a particular type, can be expanded in width by 6, and in height by 5 mm less, lower for canvases without upholstery.

Doors of type C can be used with doors with heavy fittings and a reinforced frame according to GOST 6629.

1.5. Restore the next structure of the mental designation (brand) of the doors:

x x x- x xx

I-Designated to the standard

Letters that mean: A, B and C - variants of small ones of the same size; G - deaf doors; K - doors with hitny canvases; L - door lіvі; P - doors with a threshold; T - the doors are fired up; U - insulated doors; Ш - shield doors; 0-1 or O-Z - 0-2 - type of sheathing

Opening width, dm

Opening height, dm

Door type 1.1 (N, S abo L)

Virobu type: D - doors

Vidannya official Peredruk fenced

Apply smart words

Entrance doors or tambour doors, single-sawed for an opening with a height of 21 and a width of 9 dm, glazed, with the right board sheet, with a threshold, with sheathing type 0-2:

DN21-9 PShch02 GOST 24698-81

Those same, with the left navazhka of the frame canvas:

DN21-9LP DERZHSTANDARD 24698-81

The same ones with hitny canvases for the opening with a height of 24 and a width of 15 dm:

DN24-15K GOST 24698-81

Doors of service, double-deaf for an opening with a height of 21 and a width of 13 dm, insulated:

DS21-13GU GOST 24698-81

A single-panel hatch for a hole with a height of 13 and a width of 10 dm:

DL13-10 GOST 24698-81

2. VIMOGY TO CONSTRUCTION

2L. The doors are made to meet the requirements of GOST 475 and the same standard for working chairs, hardened in accordance with the established procedure.

2.2. The design, shape and type of doors according to the fault are assigned to the characteristic. 2-5; 6-13.

2.3. Cloths of shield doors are made from the core of the shield, calibrated according to the composition of the wooden slats.

The doors are lined with materials according to GOST 475 parts, which can be brought to the doors of increased moisture resistance.

For the use of strong door trim from the outer side with profile rails per GOST 8242 for a ball of parchment per GOST 2697 or for galvanized steel sheathing per TU for steel of a specific type, solid fiberboard of grades T or T-S, T-P, T-SP per GOST 45 is allowed or waterproof plywood brand FK according to GOST 3916.1 or GOST 3916.2. Tambour doors can be made without sheathing with wooden laths. The rails are fastened with screws GOST 1144 or with GOST 4028 screws with a length of 40 mm with anti-corrosion coatings. The maximum kr_plen krіplen - 500 mm. The fastening in the skin row is due to the butt stitching on one level along the entire width of the canvas.

2.4. The lower parts of the H-type door leafs are to be protected by wooden slats with a thickness of 16-19 mm or swags with decorative paper-ball plastic with a thickness of 1.3-2.5 mm according to GOST 9590 *, overhard fiberboard with a thickness of 3.2-4 mm according to GOST 4598 , sheet galvanized steel. Wood and plastic materials are fastened with waterproof glue and screws with anti-corrosion coatings, and steel smugs are fastened with 30-40 mm bolts according to GOST 1144. The perimeter fastening is 100 mm. Razmіri zahishnikh planks and smog are shown in fig. 6-11.

2.5. Cloths and boxes of fireproof and insulated doors of type C should be protected with thin-sheet galvanized steel 0.35-0.8 mm per specification for steel of a particular type along all surfaces on both sides, as indicated in fig. 12. The sheets began to close together at a single fold.

2.6. Cloths of important burning doors of type Z both sides are covered with balls of asbestos cardboard with a thickness of 5 mm according to GOST 2850.

Cloths of insulated doors of type Z are covered from one side with a ball of soft fiberboard with a thickness of 12 mm according to GOST 4598. Along the perimeter of the door leaf from the side of the insulation, fasten with flowers or self-tapping screws of wooden slats 12x30 mm, crack fastening - 100-150 mm.

2.7. For folding doors, fix a door stopper 4-5 mm according to GOST 111.

It is also difficult to find on a window of 800 mm, or less at the bottom of the canvas, and with different glasses of a large format, it is necessary to install a fence.

Apply the installation of zahisnyh fences in addition 2.

Tovshchina skla, design of zahisnih gratings and changes in the design of doors, connected with the installation of electric locks, must be ordered at work chairs.

Dimensions of doors

Entrances and tambours

Notes:

1. Schemes of doors are shown from the side of the facade.

2. The numbers above the door schemes mean opening in decimeters.

3. Rosemary in shackles is given for doors 21-15A, 21-19, 24-15A and 24-19 with smart canvases.

4. Doors 21-9 and 21-13A are used for single-surface buds and small spaces.

Design, shape and type of doors

Shield doors

DN21-13A DN 21~10

Dbvrі ramkovі

DN21-10A DNI ~ 136 DN21-15B

sch.

DN20-10A DN20-13B

Odo_^_9oo_

Type C. Doors are shielded and insulated

Retin of door details

type

Shield doors

Peretin A1

1 - strengthening gasket zgidno z GOST 10174; 2 - lining of DBP grades ST plі T-B zavtovshki 1.2-5 mm according to GOST 4598; 2 - rail 12x12 mm; 4 - gasket with porous gum zavtovshki 2 mm according to GOST 7118; 5 - screw 1-1x10 zgіdno z GOST 1144, screw 200 mm; 6 - mounting board

Notes:

1, It is allowed to stick plastic sockets,

2, It is allowed to install the mounting boards of the other design,

Chort, 6

GOST 24698-81

Peretin AS

1 - facing fiberboard grades ST or T-V zavtovshki 3.2-4 mm according to GOST 4598; 2 - narrowing gasket zgidno s GOST 10174

2.8. For protection against mechanical damage, reduction of noise and heat loss of doors of type H, they are equipped with door locks of type ZD1 according to GOST 5091, sealing gaskets according to GOST 10174 or with porous gum according to GOST 7338, door stops type UD1 according to DST 5, shutters type ZT or latches ShV according to GOST 5090.

1 - strengthening gasket zgidno z GOST 10174; 2- facing fiberboard grades T, T-S, T-P and T-SP group A tovshchina 3.2-4 mm according to GOST 4598; 3 - sheathing brand 0-3 according to GOST 8242; 4- glassine according to GOST 2697; 5 - cladding of fiberboard grades ST or ST-S zavtovshki 3.2-4 mm zgidno z GOST 4598; 6 - socket 19x13 mm

Peretin B1 54

D'eri frames

Pereriz BZ

Peretin 54

1 - strengthening gasket zgidno z GOST 10174; 2 – sealing on adhesives with increased water resistance; 3 - screw 1-3x40 zgіdno z GOST 1144, screw 200 mm; 4 - gasket with porous gum zavtovshki 2 mm according to GOST 7338; 5-rail 12x20 mm; 6 - mounting board

1 - narrowing gasket zgidno s GOST 10174

D'erіramochnі z hitnihnyh canvases Peretin G1 Pereriz G2

1 - spring loop according to GOST 5088; 2 - paper-layered plastic according to GOST 9590; 3 - mounting board

2.9. The need to complete the doors with locks, according to GOST 5089, is to be blamed for the locking.

2.10. Raztashuvannya priladіv їх types induced at the addendum 3.

2.11. At the request for the delivery of doors, the following may be indicated:

The number of doors according to the brands that are assigned to the standard;

Type and color of processing;

Tovshchina warehouse;

Appliance specification.

T i p C

Take a shield

Peretin D1 Peretin D1

1 - gasket with porous gum zgidno with GOST 7338; 2 - sheet steel galvanized with a thickness of 0.5 mm; 3- cladding of fiberboard grade ST or T-V zavtovshki 4 mm according to GOST 4598; 4 - asbestos cardboard according to GOST 2850; 5-m'yaka fiberboard brand M-1 tovshchina 12 mm according to GOST 4598; 6-rail wooden 12x30 mm;

7- screws 1-4x40 according to GOST 1144, crochet 200 mm

T i p L

Peretin Zh1

Luki ta lazi

Pereriz ZhZ

1 - sheet steel galvanized with a thickness of 0.5 mm; 2 - handle-bracket PC according to GOST 5087;

3 boards; 4 - mineral wool slabs on a synthetic finish GOST 9573;

5 - gasket with porous gum 6x20 mm zgidno with GOST 7338; 6 - loop PN1-130 according to GOST 5088; 7 - wood stop

tovshchina 50 mm

ADDITION 1 Dovidkove

ROZMIRI DOOR OPENINGS AT THE WALLS

Note. At the temples, there are openings for the doors that are pierced.

APPLY THE INSTALLATION OF THE ZAKHISNY GARDEN

Wooden fence

metal fences

1 - wooden planks made of hard-leaved porous; 2 - steel bar; 3 - rafter plank made of smug steel

POSITIONING OF FITTINGS AT THE DOOR

Single door type I and C

Double doors type I and C

1 - curved doors ZD1 according to GOST 5091; 2 - loops PNZ-130; PN1-150, PN2-150, PNZ-150 according to GOST 5088; 3- zasuvka ZT or latches ShV according to GOST 5090;

4 - handle-bracket according to GOST 5087

Door type L

1 - a loop for a counterweight; 2 - handle-bracket according to GOST 5087; 3 - open the screw M5; 4 - loops PN1-130 according to GOST 5088; 5 - wooden stop

Notes:

1. Curves are not installed at type Z doors.

2. Locks are installed at the paddocks, which are used by working chairs.

3. Staple handles can be installed vertically or horizontally.

4. Loops for counters are installed in single-panel hatches. It is allowed to fix the loops of the other design.

INFORMATION DATA

1. DISCLAIMER AND INTRODUCED by the Sovereign Committee for Civil Life and Architecture under the Derzhbudi SRSR

2. STATEMENTS AND INTRODUCTIONS BY THE DIA to the praise of the Sovereign Committee of the SRSR on the right of everyday life, dated April 31, 1981, No. 51

3. INTRODUCED ABOVE

4. REGULATORY AND TECHNICAL DOCUMENTS SUBMITTED

	Item number, program		Item number, program
GOST 111-2001		GOST 5088-2005	2.2,2.4, supplement 3
		GOST 5089-2003
GOST 1144-80		GOST 5090-86	2.8, supplement 3
GOST 2697-83		GOST 5091-78	2.8, supplement 3
GOST 2850-95		GOST 7338-90
GOST 3916.1-96		GOST 8242-88
GOST 3916.2-96		GOST 9573-96
GOST 4028-63		GOST 9590-76
GOST 4598-86		GOST 10174-90
GOST 5087-80	2.2, supplement 3

5. REVIEW. Zhovten 2009

Editor M.I. Maksimova Technical editor V.M. Prusakova Proofreader M.S. Kabashova Computer layout L.A. Circular

Signed before each other 02.10.2009. Format 60x84 "/ . Offset paper. Times typeface. Other offset. Printed sheet 2.32.

FSUE “STANDARTINFORM”, 123995 Moscow, Granatny prov., 4

Instructed at the branch of FSUE "STANDARTINFORM" - type. "Moscow Drukar", 105062 Moscow, Lyalin prov., 6.

/ GOST 24698-81

Updated: 09.02.2006

GOST 24698-81

UDC 691.11.028.1 : 006.354 Group Z32

STATE STANDARD RSR

WOODEN DOORS FOR RESIDENTIALS I

GROMADSKIKH BUDIVEL

Tipi, design and expansion

Wooden external doors for dwellings and public buildings.

Types, structure and dimensions

OKP 53 6110 ; OKP 53 6196

Decree of the Sovereign Committee of the SRSR on the right of everyday life on April 13, 1981. No. 51

01/01/1984

ROZROBLEN by the State Committee for Civil Life and Architecture under the Derzhbudi SRSR

VICONAUTSI

Yu. A. Argo (certifier of topics), Ph.D. tech. sciences; I. V. Strokov; I. S. Posilska; G. G. Kovalenko; Z. A. Burkova; G. V. Levushkin

INTRODUCED by the Sovereign Committee for Civil Life and Architecture under the State Council of the USSR

Deputy head S. G. Zmeul

STATEMENTS AND INTRODUCTIONS BY THE DIA DECREE OF THE SRSR Sovereign Committee on the Rights of Life on April 13, 1981 No. 51

Non-compliance with the standard is followed by law

The standard does not appear on the doors of unique public buildings: railway stations, theatres, museums, sports palaces, exhibition pavilions, palaces of culture.

1. TIPI, ROZMIRI AND MARK

1.1. Doors, which are prepared according to this standard, fall into the following categories:

H - entrances and tambours;

C - services;

L - hatches and lazi.

1.2. Doors of type H are made from shield and frame canvases. Frame canvases can be smart. Doors of types C and L are made from panel boards. Shield cloths can be prepared with batten sheathing.

Doors of types H and C are made with single-panel and double-panel, glued and blind canvases, with a threshold and without a threshold.

1.3. All doors, which are prepared according to this standard, are brought up to the doors of increased moisture resistance.

1.4. Dimensional dimensions of the doors according to the requirements are indicated on the characteristic. 1. The dimensions on the armchairs are given to the standard for non-barrier types and details in mm. Rosemary opened at the preliminary addendum 1.

Doors of type C can be equipped with doors with a strong seal and a reinforced frame according to GOST 6629-74.

1.5. Such a structure of mental designation (brand) of doors is being established.

Apply clever words:

entrance doors or tambour doors, single-sawed for an opening with a height of 21 and a width of 9 dm, glazed, with a right-handed shield canvas, with a threshold, with type 2 sheathing:

DN 21-9PShchR2 GOST 24698-81

the same, with the left navazhka of the frame canvas:

DN 21-9LP GOST 24698-81

entrance doors or tambour doors with smart canvases for an opening with a height of 24 and a width of 15 dm:

DN 24-15K GOST 24698-81

double-deaf service doors, for an opening with a height of 21 and a width of 13 dm, insulated:

DS 21-13GU GOST 24698-81

a single-panel hatch for a hole with a height of 13 and a width of 10 dm:

DL 13-10 GOST 24698-81

2. VIMOGY TO CONSTRUCTION

2.1. The doors of the hinged vygotovlyatsya vіdpovіdno up to GOST 475-78, which is the standard for working chairs, hardened in the prescribed manner.

2.2. The design, shape and type of doors according to the fault are assigned to the characteristic. 2 - 5, and the expansions of the resizes - in fig. 6 - 13.

2.3. Cloths of shield doors are made from the core of the shield, calibrated according to the composition of the wooden slats.

Door cladding is carried out with materials up to GOST 475-78 at the part, which can be applied to the doors to increase moisture resistance.

For sutsile door siding from the outer side with profiled rails per GOST 8242-75 for parchment ball per GOST 2697-75 or for galvanized steel siding per GOST 7118-78, hard wood-fiber boards of the T-440 FK grade per GOST 3916-69 are allowed. Tambour doors can be made without sheathing with wooden laths. The rails are fastened with screws GOST 1144-80 or with GOST 4028-63 flowers with a length of 40 mm with anti-corrosion coating. The maximum kr_plen krіplen - 500 mm. The fastening in the skin row is due to the butt stitching on one level along the entire width of the canvas.

2.4. The lower parts of the door leafs of type H are due to the protection of wooden planks with a thickness of 16 - 19 mm or swags with decorative paper ball plastic with a thickness of 1.3 - 2.5 mm according to GOST 9590-76, overhard wood fiber boards with a thickness of 3.2 - 4 mm for GOST 4-74, thin-sheet galvanized steel. Wood and plastic materials are fastened with waterproof glue and screws with anti-corrosion coatings, and steel smugs are fastened with 30-40 mm bolts according to GOST 1144-80. Krok fastening outside the perimeter of 100 mm. Razmіri zahishnikh planks and smog are shown in fig. 6 - 11.

2.5. Cloths and boxes of fireproof and insulated doors of type C should be protected with thin-sheet galvanized steel 0.35 - 0.8 mm according to GOST 7118-78 on all surfaces of both sides, as indicated in fig. 12. The leaves began to merge into a single fold.

2.6. Cloths of high-rise doors type Z both sides are covered with balls of asbestos cardboard with a thickness of 5 mm according to GOST 2850-75.

Cloths of insulated doors type Z are covered from one side with a ball of soft wood fiber boards with a thickness of 12 mm according to GOST 4598-74. On the perimeter of the canvas, on the side of the insulation, fasten with flowers or screws wooden slats 12 30 mm, fastening 100 - 150 mm.

2.7. For folding doors, fix a door stopper 4 - 5 mm according to GOST 111-78.

It is also difficult to find on a window of 800 mm, or less at the bottom of the canvas, and with different glasses of a large format, it is necessary to install a fence.

Apply the installation of winter fences in the recommended addendum 2.

Tovshchina skla, design of zahisnih gratings and changes in the design of doors, connected with the installation of electric locks, must be ordered at work chairs.

2.9. The need to complete the doors with locks, according to GOST 5089-80, is due to buti is designated in the lock.

2.10. Raztashuvannya priladіv and їх tipi induced at the shoe's lanyard addendum 3.

2.11. At the request for the delivery of doors, the following may be indicated:

the number of doors according to the brands that are assigned to the standard;

type and color of processing;

tovshchina warehouse;

specification of accessories

DIMENSIONS OF DOORS ROSE